Technical article 127957

Host Bus Adapter (HBA) Driver - ahci Driver version 2.0a, IHVVERSION 1.3.1

OpenServer Definitive 2018UnixWare 7 Definitive 2018OpenServer 6UnixWare 7

Written

Problem

What is the ahci driver version 2.0a HBA for OpenServer 6 Definitive 2018 and UnixWare 7 Definitive 2018?

HARDWARE: All of the AHCI v1.3.1 Specification is fully supported with the exception port multipliers and power management.

Solution

The ahci Driver provides the following device driver:

ahci - SATA AHCI

Version 1.1 of this driver adds support for compliant SATA tape device.

Version 1.2 fixes a problem where the ahci controller assumes it is the primary/boot controller for the system when it is not resulting in a boot failure post ISL.

Version 1.2.1 enables support on the bhyve hypervisor available on OpenServer 10 and other FreeBSD-based operating systems.

Version 2.0 has the following improvements:

- added support for virtualbox environments - fixed panic in virtual environments under heavy load - fixed detection of devices on newer chipsets such as the Intel C236 - ported to OpenServer 5 Definitive

Version 2.0a has the following bug fixes:
- fixed a panic when replacing a cartridge in a Dell PowerVault
  RD1000 Removable Disk Storage.  (The fix is to set correctly
  a return value.)
- resolved an event registration issue as part of a fix to avoid
  a panic on start up when an empty Dell PowerVault RD1000
  Removable Disk Storage device is attached.

This device driver should be installed via patchck and/or pkgadd after an ISL installation.

-------------------------------------------------------------------------
I. Installation

Either use patchck to install this device driver or follow this procedure:

1. Download the hba.ahci.2.0a.image file to the /tmp directory on your machine.

2. As root, add the package to your system using these commands:

$ su -
Password: <type your root password>
# pkgadd -d /tmp/hba.ahci.2.0a.image

Alternatively, this package may be installed in quiet mode. To do this, use these commands:

$ su -
Password: <type your root password>
# pkgadd -qd /tmp/hba.ahci.2.0a.image all
3.  Reboot the system after install this package.
------------------------------------------------------------------------
II. Software Notes
1.  This device driver can only be installed via pkgadd or patchck on an
    OpenServer 6 Definitive 2018 (D2M1) or UnixWare 7 Definitive 2018 (D2M1)
    system.   This device driver is not available during a Definitive 2018 ISL
    installation.
2.  If you intend to use a Dell PowerVault RD1000 Removable Disk Storage
    on an OpenServer 6 Definitive 2018 or a UnixWare 7 Definitive 2018
    system:

- Disconnect the RD1000. - Install OpenServer 6 Definitive 2018 or UnixWare 7 Definitive 2018 and configure the AHCI device driver. - Install PTF 9150 or SLS OSS726 to get an additional required fix to the sd01 device driver. - Install this AHCI device driver. - Reboot your system. - Reconnect the RD1000.

3.  When installing this device driver, the postinstall script may take
    several minutes to run.
4.  Additional information for this device driver will be published as
    technical articles in our knowledge base, if available.

From the Xinuos technical article database, record 127957. Reproduced with permission. The original is at www.sco.com/ta/127957, which is reachable but blocked from search engines.

Next step

Need this fixed rather than explained?

Tell us the release, what the system runs and what it is doing. We will reply by email with what we would do next.

  • You deal with the people who do the work
  • No obligation, and no upgrade required before we will help
  • We tell you plainly if something is not worth doing

Send an enquiry

We reply by email. If a server is down, say so in the first line. You can also write to help@scoexpert.com.