Problem
How can I get a Fujitsu Siemens Computers' PRIMERGY SX30
Cluster Storage Subsystem to work in an HA shared storage
environment under SCO OpenServer 6.0.0 and SCO UnixWare
7.1.3 / 7.1.4?HARDWARE: Fujitsu Siemens Computers (FSC) PRIMERGY SX30 Cluster SCSI Storage subsystem. FSC LSI MegaRAID Ultra 320-2 (PCI Dual Channel). FSC LSI MegaRAID Ultra 320-2X (PCI-X Dual Channel). FSC LSI MegaRAID Ultra 320-2E (PCI Express Dual channel). 2x FSC PRIMERGY TX200-S2 (Tower) 2x FSC PRIMERGY RX200-S2 (Rack) 2x FSC PRIMERGY TX300-S2 (Tower) 2x FSC PRIMERGY RX300-S2 (Rack)
Solution
Before proceeding with the configurations, make sure you follow the below points step-by-step:
1- Make sure that both Nodes (servers) are disconnected from the PRIMERGY SX30 Storage Subsystem.
2- check that the following BIOS and firmware are up-to-date.
NOTES: The latest BIOS and firmware for the FSC LSI MegaRAID
controllers are available on FSC Website:http://support.fujitsu-siemens.com/globalflash/ScsiController/FSC LSI MegaRAID Ultra 320-2 BIOS = G302 & Firmware = 1F45
FSC LSI MegaRAID Ultra 320-2X BIOS = H430 & Firmware = 420W
FSC LSI MegaRAID Ultra 320-2E BIOS = H430 & Firmware = 516DIf your FSC LSI MegaRAID controller is not up-to-date with the above BIOS and firmware releases, then it is IMPORTANT that you perform the BIOS and Firmware upgrade on the FSC LSI MegaRAID controllers.
3- While the SCSI cable is disconnected between the two servers (FSC LSI MegaRAID) and the PRIMERGY SX30 cluster, boot both servers and enter the LSI MegaRAID browser based BIOS configuration utility (WebBIOS) by keying <Ctrl><H>.
4- Make sure you have the following LSI MegaRAID BIOS settings.
On Node (Server) one:Under "Adapter Properties" link,
Cluster Mode * = Enabled (Default is Disabled)
Initiator ID = 7 (Default is 7)
Adapter BIOS *, ** = Disabled (Default Enabled)
Fast Initialization * = Enabled (Default is Disabled)
Class Emulation Mode = Mass Storage (Default is Mass Storage)* Need changing from the default setting.
** Adapter BIOS is disabled, as it will not be used for OS
booting.Save the setting and power off the server.
On Node (Server) two:
Under "Adapter Properties" link,
Cluster Mode * = Enabled (Default is Disabled)
Initiator ID * = 6 (Default is 7)
Adapter BIOS *, ** = Disabled (Default Enabled)
Fast Initialization * = Enabled (Default is Disabled)
Class Emulation Mode = Mass Storage (Default is Mass Storage)* Need changing from the default setting.
** Adapter BIOS is disabled, as it will not be used for OS
booting.VERY IMPORTANT, that the Initiator ID on the second LSI MegaRAID controller should be set to ID=6. If left at 7, then the cluster functionality within the controller will fail due to conflict with the Initiator ID on the first LSI MegaRAID controller.
Save the setting and power off the server.
5- Connect (Cable) the first Node LSI MegaRAID ONLY to the PRIMERGY SX30 Storage subsystem. Leave the second one not connected at this stage.
Power on Node one and enter the MegaRAID RAID configuration utility "WebBIOS" with <Ctrl><H> and check that the controller sees all the physical disks on the PRIMERGY SX30. Setup the Logical RAID drives (Array disks).
Save the settings and initialize the newly created logical raid drives. The initialization will be very fast. Do not reboot the server at this stage yet.
6- Connect (Cable) the second Node LSI MegaRAID to the PRIMERGY SX30 Storage Subsystem. Power on Node two and enter the MegaRAID RAID configuration utility "WebBIOS" with <Ctrl><H> and check that the controller sees all the configured logical RAID drives on the PRIMERGY SX30, that where created by Node one. If so, then now both nodes LSI MegaRAID are correctly cabled and setup to work with the PRIMERGY SX30 Storage Subsystem in a Cluster (shared Storage) environment.
7- You can now install SCO OpenServer 6.0.0 or UnixWare 7.1.3 / 7.1.4 on the first node and then create in the post installation the Unix filesystems (via UW7 "diskadd" or OSr6 "mkdev hd") on the Logical RAID Drives in the PRIMERGY SX30 Storage Subsystem.
8- Install SCO OpenServer 6.0.0 or UnixWare 7.1.3 / 7.1.4 on the second node. SCO UnixWare 7.1.3 / 7.1.4 will auto detect the generated filesystems on the PRIMERGY SX30 and will create the associated devices for the filesystems.
For OpenServer 6.0.0, you need to run "mkdev hd" and choose the created logical RAID drives on the PRIMERGY SX30 and within "divvy" configuration ONLY update the filesystem names (To be the same as in the first node).
WARNING: "FS" field should be set to "No"With this, the associated devices for the filesystems will be created.
Both systems are now ready to be used for shared storage HA environment.
NOTES: The above is NOT an SCO officially supported solution, but has
been setup and reported by SCO field engineers to work in HA
environment. See also
TA126628 "how can I get a DELL PowerVault 220S / 221S Storage Subsystem to work in an HA shared storage environment under SCO OpenServer 6.0.0 and SCO UnixWare 7.1.3 / 7.1.4?