Technical article 126479

How can I get started with the Online Data Manager (ODM) for SCO OpenServer 6

OpenServer 6.0.0

Written · Last revised

Problem

I want to install Online Data Manager on SCO OpenServer 6. Where can I get this product from?

Solution

Online Data Manager for SCO OpenServer 6 is included in Maintenance Pack 2 for OpenServer 6 (osr600mp2) Distribution CD.

This CD is included in the current OpenServer 6.0.0 media kit and can also be downloaded from SCO web site at the following url:

http://www.sco.com/support/download.html
To install:
- ODM requires that Maintenance Pack 3 is previously installed on
  the system or latest Maintenance Pack after MP3 BEFORE ODM is
  installed.  If you install ODM after MP3 then MP3 would need to be
  re-installed!  MP3 contains a number of very important ODM fixes.

- Install ODM for OpenServer 6 but do not reboot after the installation!

- Depending on what you wish to achieve with ODM depends on the license you purchase:

http://www.sco.com/products/openserver6/SCO_data_online_DS.qxd.pdf

Add the ODM "Mirroring" license via "scoadmin license" manager.

See:
http://osr600doc.xinuos.com/en/ODM_oi/_Online_Data_Manager_oi.html

Please Note: Please contact your SCO product supplier to obtain appropriate license(s)

- Reboot.

Now you are ready to use ODM under OpenServer 6.0.0.

The first step is to run "vxinstall" and see the guide below for more details.

Generally, it is not recommended to use ODM on top of hardware RAID unless there is a specific need.

It is not recommended to encapsulate the root disk with ODM unless there is a specific need and has been tested thoroughly.

This generally fails because:

a) the IDE, SCSI or SATA controller in use is not able to boot from the second disk.

b) there is no vtoc written to the second disk prior to ODM's
   installation.  This can be done by running "mkdev hd" and adding
   the second disk.  The options can be defaulted, the important
   thing is that a 'vtoc' is created.  Then reboot.
c) if the second disk already has an operating system installed then
   the disk's master boot record (mbr) will be configured for this
   operating system.  This can be done pre or post root disk
   encapsulation with the "fdisk" command, for example:
# fdisk /dev/rdsk/c0b1t0d0p0
Total disk size is 9729 cylinders (76316.6 MB)
                                           Cylinders               Approx
Partition   Status       Type        Start    End   Length    %      MB
=========   ======    ===========    =====    ===   ======   ===   ======
    1       Active    UNIX System       0    2431    2432     25    19077.2
SELECT ONE OF THE FOLLOWING:
     0.   Overwrite system master boot code
     1.   Create a partition
     2.   Change Active (Boot from) partition
     3.   Delete a partition
     4.   Exit (Update disk configuration and exit)
     5.   Cancel (Exit without updating disk configuration)
Enter Selection: 0

and selecting 0 to rewrite the master boot record.

Once you have done this, test this by shutting the server down, removing the first disk and re-powering, and the server should boot from the second disk and show, for example:

bash-3.2# sdiconfig -l
0:1,2,0: HBA     : (ide,2) Generic IDE/ATAPI
  1,0,0: DISK    : ST380211AS              3.AA
1:0,2,0: HBA     : (ide,1) Generic IDE/ATAPI
  0,0,0: CDROM   : BENQ    COMBO CB523C    G.PB
and in "vxprint":
          # vxprint
Disk group: rootdg
TY NAME         ASSOC        KSTATE   LENGTH   PLOFFS   STATE    TUTIL0  PUTIL0
dg rootdg       rootdg       -        -        -        -        -       -
dm disk01       c0b1t0d0s7   -        39036926 -        -        -       -
dm rootdisk     -            -        -        -        NODEVICE -       -
v  rootvol      root         ENABLED  36934650 -        ACTIVE   -       -
pl rootvol-01   rootvol      DISABLED 36934650 -        NODEVICE -       -
sd rootdisk-02  rootvol-01   DISABLED 36934650 0        NODEVICE -       -
pl rootvol-02   rootvol      ENABLED  36934650 -        ACTIVE   -       -
sd disk01-03    rootvol-02   ENABLED  36934650 0        -        -       -
v  standvol     fsgen        ENABLED  81918    -        ACTIVE   -       -
pl standvol-01  standvol     DISABLED 81918    -        NODEVICE -       -
sd rootdisk-03  standvol-01  DISABLED 81918    0        NODEVICE -       -
pl standvol-02  standvol     ENABLED  81918    -        ACTIVE   -       -
sd disk01-01    standvol-02  ENABLED  81918    0        -        -       -
v  swapvol      swap         ENABLED  2010350  -        ACTIVE   -       -
pl swapvol-01   swapvol      DISABLED 2010350  -        NODEVICE -       -
sd rootdisk-01  swapvol-01   DISABLED 2010350  0        NODEVICE -       -
pl swapvol-02   swapvol      ENABLED  2010350  -        ACTIVE   -       -
sd disk01-02    swapvol-02   ENABLED  2010350  0        -        -       -

and to prove there is no primary root disk:

  # fdisk
UX:fdisk: ERROR: Default device (/dev/rdsk/c0b0t0d0p0) cannot be opened

Once installed, to control ODM using the Graphical Interface, using "vxva" from the Desktop or using a X product from your desktop, such as Xming.

"vxva" installs into /usr/X11R6/bin and can also be selected from "scoadmin".

See also

http://osr600doc.xinuos.com/en/ODM_oi/_Online_Data_Manager_oi.html

TA110340, "UnixWare 7, How can I get started and use the VERITAS Volume Manager to concatenate (span) non-root disks together?"

and the 2006 Forum Technical Presentation at:

11 Protect and Manage your SCO OS and Data using ODM and Mirroring [PPT]

http://www.sco.com/2006forum/breakouts/breakout/111-127_stetzel_d_ODM_Forum2006.ppt

From the Xinuos technical article database, record 126479. Reproduced with permission. The original is at www.sco.com/ta/126479, which is reachable but blocked from search engines.

Next step

Need this fixed rather than explained?

Tell us the release, what the system runs and what it is doing. We will reply by email with what we would do next.

  • You deal with the people who do the work
  • No obligation, and no upgrade required before we will help
  • We tell you plainly if something is not worth doing

Send an enquiry

We reply by email. If a server is down, say so in the first line. You can also write to help@scoexpert.com.