Technical article 126807

How to configure a MultiTech MT5634MU USB Modem under SCO OpenServer 6.0.0 & UnixWare 7.1.4?

OpenServer 6.0.0UnixWare 7.1.4

Written · Last revised

Problem

How can I configure a MultiTech MT5634MU MultiMobile USB modem or a MT5634ZBA V.92 USB Modem under SCO OpenServer 6.0.0 & UnixWare 7.1.4?

Please Note: I do not want to use a "standard" Modem from the list in the SCO Modem Manager.

HARDWARE: MultiTech MT5634MU MultiMobile USB MultiTech MT5634ZBA V.92 USB

Solution

Under SCO OpenServer & UnixWare, there is no hard coded Modem drivers, but modem definition files that contain the correct modem stings for the initialization on dialup or dialin.

These definition file are located at
/etc/uucp/default

We only need to define the correct Modem strings.

Before your start, make sure you have installed the following:

For SCO UnixWare 7.1.4
Maintenance Pack 3:
http://www.sco.com/support/update/download/release.php?rid=126
ptf9052g:
http://www.sco.com/support/update/download/release.php?rid=249
Maintenance Pack 3 USB Supplement (uw714usb):
http://www.sco.com/support/update/download/release.php?rid=193

(You only need to install the udienv package and the usb package, defere the ptf9052d, superseded by ptf9052g).

For OpenServer 6
Maintenance Pack 2:
http://www.sco.com/support/update/download/release.php?rid=133
oss706c supplement:
http://www.sco.com/support/update/download/release.php?rid=238
OpenServer 6 USB Supplement:
http://www.sco.com/support/update/download/release.php?rid=194

Follow these steps to configure a MultiTech MT5634MU USB Modem:

Please Note: For MT5634ZBA USB Modem, you can skip step 2,3,4,5,6 below and replace any reference for MT5634MU with MT5634ZBA.

1- Plug in the MultiTech MT5634MU USB Modem.

The usbprobe should detect the USB Modem and creates USB-Serial ports for it.

To confirm:
# usbprobe
Path - Address - Description
----------------------------
+++++++ BUS #0
0 - 1 - HUB "UHCI Root Hub"
+++++++ BUS #1
0 - 1 - HUB "UHCI Root Hub"
1 - 2 - Communication "Multi-Tech Systems, Inc.
MultiModemUSB"
+++++++ BUS #2
0 - 1 - HUB "UHCI Root Hub"
+++++++ BUS #3
0 - 1 - HUB "UHCI Root Hub"
+++++++ BUS #4
0 - 1 - HUB "EHCI Root Hub"
# l /dev/usb_ser*

crw-rw-rw- 1 root root 280,103 Jun 27 16:11 /dev/usb_ser0a crw-rw-rw- 1 root root 280,104 Jun 27 16:21 /dev/usb_ser0A crw-rw-rw- 1 root root 280,102 Jun 27 16:11 /dev/usb_ser0h crw-rw-rw- 1 root root 280,101 Jun 27 16:11 /dev/usb_ser0s

where

/dev/usb_ser0A is the modem control device /dev/usb_ser0a is the non modem control device /dev/usb_ser0h is the Hardware flow control device /dev/usr_ser0s is the Software flow control device

2-
  # cd /etc/uucp/default

3- Make a copy of the MultiTech_MT5656ZBA file:

# cp MultiTech_MT5656ZBA MultiTech_MT5634MU

4- Edit the MultiTech_MT5634MU file to look like following content:

--- cut here  ---
#
# Vendor: MultiTech_Systems
# Modem : MultiTech MT5634MU
MDM_SETUP=AT&FE0\N3\Q0\J0\Q1%C0&D3S72=0S0=1
MDM_SPEAKER=ATM0
MDM_DIALCMD=ATDT
MDM_HANGUP=ATH
--- cut here ---

Please Note: You might want to look at the MT5634MU manual guide under the AT commands (Modem strings) and customize the MDM lines above.

5-
Change to the DBase directory
# cd ../DBase

6- Edit the MultiTech_Systems file and add the following line at the end of the file:

MultiTech_MT5634MU {MultiTech MT5634MU} 01 {SERENUM\MTS00B1 1}

7- Now run "scoadmin modem" and add manually the MultiTech MT5634MU.

You will see it on the list of Modems model when choosing MultiTech Systems in the Modem vendor.

BUT, we can't choose the USB Serial port where the Modem is connected to from the the Port selection. We only get Standard COM1 (tty1A , term/00m) & COM2 (tty2A, term/01m).

As a workaround, choose in the Modem port (tty1A for OSR6 or /term/00m for UW714).

8-
For UnixWare 7.1.4:
Edit /etc/uucp/Devices file and change the line

Direct term/00m,M - 57600 direct ACU term/00m,M - 57600 MultiTech_MT5634MU

to:

Direct usb_ser0A,M - 57600 direct ACU usb_ser0A,M - 57600 MultiTech_MT5634MU

For OpenServer 6.0.0:
Edit /etc/uucp/Devices file and change the line

ACU tty1A - 57600 MultiTech_MT5634MU Direct tty1A - 57600 direct

to:

ACU usb_ser0A - 57600 MultiTech_MT5634MU Direct usb_ser0A - 57600 direct

If you are using dial-in for getty, then change also the /etc/inittab file;

Se1A:234:respawn:/etc/getty -t60 tty1A m to: Se1A:234:respawn:/etc/getty -t60 usb_ser0A m

then run "init q" to reload the inittab.

Edit the /etc/conf/init.d/asyc file to make it permanent.

Also edit the /etc/gettydefs and change any entry for tty1A to usb_ser0A.

9- Once configured, to see if you can access the Modem:

# cu -l usb_ser0A dir (for 600)
# cu -l usb_ser0A     (for UW714)

You should get the "Connected" and you can issue "at" commands.

Type in " ~. " <RETURN> (Don't type the quotes), to get back to Unix command prompt.

From the Xinuos technical article database, record 126807. Reproduced with permission. The original is at www.sco.com/ta/126807, which is reachable but blocked from search engines.

Next step

Need this fixed rather than explained?

Tell us the release, what the system runs and what it is doing. We will reply by email with what we would do next.

  • You deal with the people who do the work
  • No obligation, and no upgrade required before we will help
  • We tell you plainly if something is not worth doing

Send an enquiry

We reply by email. If a server is down, say so in the first line. You can also write to help@scoexpert.com.