Problem
How can I install SCO OpenServer 6.0.0 on the new Fujitsu PRIMERGY TX300 S5 / RX300 S5?
HARDWARE: - Fujitsu PRIMERGY TX300-S5 / RX300-S5 with BIOS release R1.06.2619 (06/19/2009).
Current Release is R1.09.2619- 1x Quad core Intel Xeon E5520 Nehalem 2.26 GHz
- 4 GB Memory- LSI 1078E SAS (MegaRaid SAS) or LSI 1068E MPT SAS.
- SATA DVD-ROM drive attached to onboard Intel ICH10B SATA controller.
- Additional Intel PRO/1000 PT server adapter PCI-E Card.
IMPORTANT Note for PRIMERGY TX300-S5 / RX300-S5:
- This server was certified as compatible by SCO.
If you have any questions about this installation, please contact your SCO support provider.
- The PRIMERGY TX300-S5 and RX300-S5 have the same motherboard and components.
The TX300-S5 is a Floor Standing Tower, while the RX300-S5 is Rackmount.
Anything valid for the TX300-S5 should also be valid for the RX300-S5.
- This server does not have Legacy PS/2 Keyboard and mouse interface.
Therefore a USB Keyboard (mouse) is used for installation and post installation.
- This server does not have a legacy Floppy 1.44 MB Drive.
It is possible to use a USB Floppy Drive in order to load a HBA driver on a floppy diskette if needed.
- Currently, there is no SCO OpenServer 6.0.0 driver support for the onboard Intel 82575EB dual port controller.
A driver will be available in time with the planned "nd" package
"6.0.8h".An Intel PRO/1000 PT server adapter PCI-E Card was used for network connectivity.
- The following Boot Controllers were used for installation:
* LSI 1068E SAS 8-port MPT controller (BIOS 6.20.00.00 & FW 1.27.00.00-IR) 2x HDD 73GB 10K SAS
* LSI MegaRAID 1078E SAS controller (FW: 1.40.32-0580, WebBIOS: 2.2-16-Rel) 2x HDD 73GB 10K SAS --> RAID-1
The onboard Intel ICH10B SATA controller was used for the SATA DVD-ROM Drive with AHCI enabled.
Solution
What follows is a descriptions of the steps you should take to install SCO OpenServer 6.0.0 on these Primergy platforms:
Pre Installation
----------------- Plug the Intel PRO/1000 PT Server Adapter PCI-E card into a free PCI-E slot.
- Make the following changes in the PRIMERGY TX300-S5 BIOS setting:
Advanced --> Advanced System Configuration --> SATA AHCI Enable [Enable] Advanced --> Advanced Processor Operation --> Hyper Threading [Disabled]
Software Required
------------------ Special SCO OpenServer 6.0.0 Boot CD that has USB Code fixes, available from:
ftp://ftpput.sco.com/tmp/support/ISO/OpenServer-6.0.0Ni-boot-2008-06-23.isoThis is a 14 MB iso image and should ONLY be used for booting some modern servers that that lack a legacy PS/2 keyboard and have USB peripherals ONLY (USB Keyboard / Mouse), where the full March 2006 OpenServer 6.0.0 install CD might have issues booting from such servers.
- SCO OpenServer 6.0.0 Install CD March 2006 recut - SCO OpenServer 6.0.0 Maintenance Pack 4 (MP4) CD-1 - SCO OpenServer 6.0.0 Support Level Supplement OSS711A - SCO OpenServer 6.0.0 Maintenance Pack 4 Device Drivers
Images for the 4 items above are available from:
http://www.sco.com/support/update/download/product.php?pfid=12&prid=20Installation
------------- Boot the PRIMERGY TX300-S5 server with the special OpenServer 6.0.0 Boot CD.
If you fail to do that and boot straight from the March 2006 CD, then the ISL will hangs at the ISL copyright screen where you are prompted to enter "Continue" because the USB keyboard will not function.
- At the [boot] prompt, enter the following:
[auto boot unix] PSM=atupand then to boot enter:[boot] b- Depending on the HD boot controller, load the "megasas" or "mpt" HBA via CD-ROM media from the OSR6 MP4 Device Drivers CD.
You can also use a USB Floppy drive to load the "megasas" or "mpt" HBA.
- At the stage of the ISL where the OSR6 install CD is requested, replace the OpenServer 6 Boot CD with the OpenServer 6.0.0 March 2006 Install CD and continue the installation.
Note: One side effect of booting from the special OpenServer 6.0.0 Boot CD, is that at ISL disk/filesystem setup, you are not able to create an additional filesystems. To overcome this issue and have extra filesystems on the root HD other then (root, boot, swap and dump), use the extra 4 default ISL presented (/u, /usr/local, /tmp and /var/tmp) filesystems and create vxfs or HTFS filesystems on them. But note, the names are not editable from the ISL.
After installation, edit the /etc/default/filesys file and change the mounting points of /u, /usr/local, /tmp and /var/tmp to directories like /data1, /data2 .....etc
- Defer networking (will be done in POST INSTALLATION)
Post Installation
------------------ Boot the server: If you are using the LSI 1078E SAS raid controller, then at the OSR6 boot prompt, enter the following boot string
[Boot] PSM=atup
[Boot] bIf you fail to do that, OSR6 boot process will hang at initialization of the "megasas" driver.
In case you are using the LSI 1068E MPT SAS controller, then no need for the above boot string.
- Install OpenServer 6 MP4 and reboot (In the case of LSI 1078E SAS Raid Controller, after installing MP4, PSM=atup is no more required to be entered at every boot process)
- Install OpenServer 6 Support Level Supplement OSS711A and reboot.
- Install OSr6 "nd" package ver. 6.0.8g from OSR6 MP4 driver CD and configure the networking for the Intel Pro/1000 PT
For sample sysinfo output from an installed Server (Using LSI 1078E MegaRaid SAS controller) please see:
ftp://ftpput.sco.com/tmp/support/CHWP/Fujitsu/tx300s5/tx300s5osr6.html