Technical article 126354

How to use DVD-RAM media with a DVD-Recorder on UnixWare/OpenServer?

OpenServer 6.0.0OpenServer 5.0.7UnixWare 7.1.3UnixWare 7.1.4

Written · Last revised

Problem

My DVD-writer allows to write DVD-RAM. Can I use these media type on my SCO platform ?

Solution

DVD-RAM writers use a different way of writing the RAM media as the media is hard-sectored and therefore can be written similar to hard disk.

Therefore cdrecord/dvdrecord does not support DVD-RAM as it actually will report "unsupported DVD-RAM media" as shown below:

# cdrecord -v -checkdrive
Cdrecord-ProDVD-Clone 2.01 (i586-sco-sysv5uw7.1.4)
Copyright (C) 1995-2004 Joerg Schilling
TOC Type: 1 = CD-ROM
scsidev: '3,0,0'
scsibus: 3 target: 0 lun: 0
Using libscg version 'schily-0.8'.
Driveropts: 'burnfree'
SCSI buffer size: 32768
atapi: 1
Device type    : Removable CD-ROM
Version        : 0
Response Format: 2
Capabilities   :
Vendor_info    : 'HL-DT-ST'
Identifikation : 'DVDRAM GSA-4163B'
Revision       : 'A103'
Device seems to be: Generic mmc2 DVD-R/DVD-RW.
Current: DVD-RAM
Profile: DVD-RAM (current)
Profile: DVD-R sequential recording
Profile: DVD-RW sequential overwrite
Profile: DVD-RW restricted overwrite
Profile: DVD+RW
Profile: DVD+R
Profile: DVD+RW/DL
Profile: DVD-ROM
Profile: CD-R
Profile: CD-RW
Profile: CD-ROM
Profile: Removable Disk (current)
cdrecord: Found unsupported DVD-RAM media.
cdrecord: Sorry, no CD/DVD-Recorder or
  unsupported CD/DVD-Recorder found on this target.
Using generic SCSI-3/mmc   CD-ROM driver (mmc_cd).
Driver flags   : MMC-3 SWABAUDIO BURNFREE
Supported modes: TAO PACKET SAO SAO/R96P SAO/R96R
  RAW/R16 RAW/R96P RAW/R96R
Drive buf size : 851968 = 832 KB
Drive DMA Speed: 2889 kB/s 16x CD 2x DVD

In order to write an ISO image to a DVD-RAM you can use the readcd tool as it allows to write directly to the device although the name indicates it only allows reading.

To write an image to DVD-RAM one needs to use the "-w" option of readcd.

Example:
# readcd dev=3,0,0 -w f=/home/iso/sample.iso
Read  speed:  4155 kB/s (CD  23x, DVD  3x).
Write speed:  4155 kB/s (CD  23x, DVD  3x).
Capacity: 2236704 Blocks = 4473408 kBytes = 4368 MBytes = 4580 prMB
Sectorsize: 2048 Bytes
Copy from file '/home/iso/sample.iso' to SCSI (3,0,0) disk
end:   2236704
addr:   181529 cnt: 96
Time total: 195.316sec
Wrote 363058.00 kB at 1858.8 kB/sec.

The list of possible parameters for readcd will be printed by:

# readcd -help
readcd -help
Usage:  readcd [options]
options:
  -version      print version information and exit
  dev=target    SCSI target to use
  f=filename    Name of file to read/write
  sectors=range Range of sectors to read/write
  speed=#       set speed of drive (MMC only)
  ts=#          set maximum transfer size for a single SCSI cmd
  -w            Switch to write mode
  -c2scan       Do a C2 error scan
  -fulltoc      Retrieve the full TOC
  -clone        Retrieve the full TOC and all data
  timeout=#     set the default SCSI command timeout to #.
  debug=#,-d    Set to # or increment misc debug level
  kdebug=#,kd=# do Kernel debugging
  -quiet,-q     be more quiet in error retry mode
  -verbose,-v   increment general verbose level by one
  -Verbose,-V   increment SCSI command transport verbose level by one
  -silent,-s    do not print status of failed SCSI commands
  -scanbus      scan the SCSI bus and exit
  -noerror      do not abort on error
  -nocorr       do not apply error correction in drive
  -notrunc      do not truncate outputfile in read mode
  retries=#     set retry count (default is 128)
  -overhead     meter SCSI command overhead times
  meshpoints=#  print read-speed at # locations
  -factor       try to use speed factor with meshpoints=#
                if possible

sectors=0-0 will read nothing, sectors=0-1 will read one sector starting from 0

See also

man readcd(1)

From the Xinuos technical article database, record 126354. Reproduced with permission. The original is at www.sco.com/ta/126354, which is reachable but blocked from search engines.

Next step

Need this fixed rather than explained?

Tell us the release, what the system runs and what it is doing. We will reply by email with what we would do next.

  • You deal with the people who do the work
  • No obligation, and no upgrade required before we will help
  • We tell you plainly if something is not worth doing

Send an enquiry

We reply by email. If a server is down, say so in the first line. You can also write to help@scoexpert.com.