Technical article 126107

I cannot access the default DVD/CD-Record device when using the "cdrecord" utility on OpenServer or Unixware 7.1.4 system

OpenServer 6.0.0OpenServer 5.0.7UnixWare 7.1.3UnixWare 7.1.4

Written · Last revised

Problem

I have a notebook with a DVD-RW/CD-RW/CD-R ATAPI device attached to the secondary controller as master.

When I try to use the "cdrecord" utility to write or access the burning device, "cdrecord" fails to access the device.

From Unix it declares that the cd (/mnt) is read only, assuming /mnt is the attempted mount point.

This is an example error when I try to erase (format) a CD-RW media:

# cdrecord blank=fast
Cdrecord-ProDVD-Clone 2.01 (i586-sco-sysv5uw7.1.4)
Copyright (C)
1995-2004 Joerg Schilling
scsidev: '0,0,0'
scsibus: 0 target: 0 lun: 0
Using libscg version 'schily-0.8'.
cdrecord: Cannot do inquiry for CD/DVD-Recorder.
cdrecord: Error 0. test unit ready: scsi sendcmd: fatal
error
CDB:  00 00 00 00 00 00
cmd finished after 0.000s timeout 40s

Cause

The "cdrecord" is accessing the wrong device ID listed in the /etc/default/cdrecord.

Solution

You need to edit the /etc/default/cdrecord file and add the correct device ID.

First you need to find the exact device ID that the "cdrecord" finds on the system.

run as root the command:
# cdrecord -scanbus
Cdrecord-ProDVD-Clone 2.01 (i586-sco-sysv5uw7.1.4)
Copyright (C)
1995-2004 Joerg Schilling
Using libscg version 'schily-0.8'.
scsibus1:
1,0,0   100) 'MATSHITA' 'DVD-RAM UJ-820S ' '1.00'
Removable CD-ROM
1,1,0   101) *
1,2,0   102) HOST ADAPTOR
1,3,0   103) *
1,4,0   104) *
1,5,0   105) *
1,6,0   106) *
1,7,0   107) *

From the output, we see that the "cdrecord" was found on the SCSI-ID 1,0,0 our DVD-RW device (MATSHITA DVD-RAM UJ-820S)

Second, edit the /etc/default/cdrecord and see what the variable CDR_DEVICE is set to, our case is set to ide: CDR_DEVICE=ide

Then below the file, in the section:

# Unless you have a good reason, use speed == -1 and let
# cdrecord use its internal drive specific defaults.
#
# drive name    device  speed   fifosize driveropts
#
teac=           1,3,0   -1      -1      ""
panasonic=      1,4,0   -1      -1      ""
plextor=        1,4,0   -1      -1      ""
sanyo=          1,4,0   -1      -1      burnfree
yamaha=         1,5,0   -1      -1      ""
ide=            0,0,0   -1      -1      burnfree
cdrom=          0,6,0   2       1m      ""
change the ide line from:
ide=            0,0,0   -1      -1      burnfree
to
ide=            1,0,0   -1      -1      burnfree
then save the file.

You now will be able to access the CD-Burner device:

# cdrecord blank=fast
Cdrecord-ProDVD-Clone 2.01 (i586-sco-sysv5uw7.1.4)
Copyright (C) 1995-2004 Joerg Schilling
scsidev: '1,0,0'
scsibus: 1 target: 0 lun: 0
Using libscg version 'schily-0.8'.
Device type    : Removable CD-ROM
Version        : 0
Response Format: 2
Capabilities   :
Vendor_info    : 'MATSHITA'
Identifikation : 'DVD-RAM UJ-820S '
Revision       : '1.00'
Device seems to be: Generic mmc2 DVD-R/DVD-RW.
Using generic SCSI-3/mmc   CD-R/CD-RW driver (mmc_cdr).
Driver flags   : MMC-3 SWABAUDIO BURNFREE
Supported modes: TAO PACKET SAO
Starting to write CD/DVD at speed 4 in real BLANK mode for
single session.
Last chance to quit, starting real write    4 seconds.....
NOTE:  Additional commands that can be run are:
# cdrecord -checkdrive
# cdrecord -v -checkdrive
# cdrecord -V -checkdrive
# cdrecord -VV -checkdrive
NOTE:  Also try using the command "cdrecord -eject" and "cdrecord -load" to
       see if the CD-ROM drive has the ability to eject or load CD's from a
       command line.

cdrecord:Cannot load media with this drive! cdrecord:Try to load media by hand.

If you see the above then the CD Drive is not capable of "loading" a
CD.  The CD Tray has to be physically pushed in.

See also

man cdrecord(1)

From the Xinuos technical article database, record 126107. Reproduced with permission. The original is at www.sco.com/ta/126107, which is reachable but blocked from search engines.

Next step

Need this fixed rather than explained?

Tell us the release, what the system runs and what it is doing. We will reply by email with what we would do next.

  • You deal with the people who do the work
  • No obligation, and no upgrade required before we will help
  • We tell you plainly if something is not worth doing

Send an enquiry

We reply by email. If a server is down, say so in the first line. You can also write to help@scoexpert.com.