Technical article 117264

I have installed 4Gb of RAM into my server, but am unable to see all of it.

OpenServer 6.0.0UnixWare 7.0.0UnixWare 7.0.1UnixWare 7.1.0UnixWare 7.1.1UnixWare 7.1.2UnixWare 7.1.3UnixWare 7.1.4Open UNIX 8

Written · Last revised

Problem

I have installed 4Gb of RAM into the server, but memsize reports less than 4Gb being usable.

Cause

One cause of this could be due to some systems' HBA controllers and other PCI devices map their address space below the 4Gb range.

Because of this, the physical memory is mapped above the 4Gb address range and is usable by operating systems which support greater than 4Gb.

Solution

In order for a Unixware 7 server to recognize memory addresses beyond the 4Gb address range, PAE (Page Address Extensions) mode must be enabled.

To do this, using your favorite text editor, to edit the /stand/boot
file and add the line 'ENABLE_4GB_MEM=YES'.  When convenient,
reboot the server.  The output from the 'memsize -t' command should
now show that the system has a total of 4Gb of memory installed. See
the manpage for the memsize(1M) command.
Also, ensure that you have not installed without a license as the
Base version of the Operating system will only detect a 1GB of RAM.
This can result in the server hanging after the boot UnixWare splash
screen.  'ENABLE_4GB_MEM' can be disabled by booting and pressing
the SPACEBAR at the UnixWare splash screen to allow booting to
continue.
NOTES:    PAE mode is not supported in NSC (NonStop Clusters) and should not
          be enabled. For further details, see Technical Article 117263, "Is it
          possible to address more than 4GB of physical memory with NonStop
          Clusters?"
TROUBLESHOOTING:

If it still fails then try selectively disabling ranges of memory with the "memadjust" boot parameter. i.e. try booting in PAE mode with all the memory above 4G disabled. ie. "memadjust-=4G-64G". "memadjust" is cumulative, so you can disable multiple chunks.

The amount of memory available to your SCO Unix operating system will also depend on the licenses used. You may need to purchase additional memory licensing to support the amount of memory you have to a limit of 64GB (Memory licensing is not incremental).

To check the amount of memory you have and to see what is fully accessible run:

# memsize -alt

See also

ta117263, "Is it possible to address more than 4GB physical memory with NonStop Clusters?"

ta116342, "What is Support Level Supplement (SLS) PTF7715b, the UnixWare 7.1.1 Maintenance Supplement, Volume 1 of 3?"

ta116363, "What is Support Level Supplement (SLS) PTF7716b, the UnixWare 7.1.1 Maintenance Supplement, Volume 2 of 3?"

ta115802, "What is Support Level Supplement (SLS) PTF7717a, the UnixWare 7.1.1 Maintenance Supplement, Volume 3 of 3?"

http://docsrv.sco.com:80/search97en_US.ISO8859-1/SM_basics/saT.config_lpm.html

From the Xinuos technical article database, record 117264. Reproduced with permission. The original is at www.sco.com/ta/117264, which is reachable but blocked from search engines. Xinuos marks this article against a retired product line. That refers to the product’s lifecycle, not to whether the advice still works — plenty of it still applies to running systems.

Next step

Need this fixed rather than explained?

Tell us the release, what the system runs and what it is doing. We will reply by email with what we would do next.

  • You deal with the people who do the work
  • No obligation, and no upgrade required before we will help
  • We tell you plainly if something is not worth doing

Send an enquiry

We reply by email. If a server is down, say so in the first line. You can also write to help@scoexpert.com.