Technical article 126646

OSR6/Unixware7: When reading data via cpio from a tape I get the following error: UX:cpio: HALT: medium's unformatted and general checking the automated tape installaton

OpenServer 6.0.0UnixWare 7.1.3UnixWare 7.1.4

Written · Last revised

Problem

When reading data via cpio from a tape I get the following error:

UX:cpio: HALT: medium's unformatted
or
UX: cpio: HALT: Medium is unformatted

What's causing this and how can I test the automated addition of tape device(s)?

Cause

You have an issue with either how the tape has been added to the server or a hardware issue with either the controller, lead, tape drive or tape media.

Check /usr/adm/syslog for any CHECK CONDIDITION errors from the SCSI controller driver.

Solution

1.  Check the tape is listed correctly in "/sbin/sdiconfig -l", eg:
1:0,7,0: HBA     : (adst70,1) Adaptec Ultra160
  0,6,0: TAPE    : BNCHMARKDLT1            5538
2.  Try the commands with variable tape blocking set:
For UW7: tapecntl -v
For OSR6: tape -a 0 setblk
3.  Ensure that if you have used the "-B" or "-C<value>"
that that same value is also used to read or view the tape.
For example, to backup:
# find . -print | cpio -ocv -C32768 -O/dev/rct0
To restore:
# cpio -ivdumc -C32768 -I/dev/rct0
4.  Check the /dev/rmt/ctape1 is correctly assigned to the device
    listed in "sdiconfig -l" command with "devattr", eg:
# devattr /dev/rmt/ctape1
ctape1
SCSI
65536
/dev/rmt/c1b0t6l0
/dev/erct0,/dev/nrct0,/dev/rct0,/dev/rmt/c0s0,/dev/rmt/c0s0n,/dev
/rmt/c0s0nr,/dev/rmt/c0s0r,/dev/rmt/c1b0t6l0n,/dev/rmt/c1b0t6l0nr
,/dev/rmt/c1b0t6l0r,/dev/rmt/c1b0t6l0u,/dev/rmt/ctape1,/dev/rmt/n
rtape1,/dev/rmt/ntape1,/dev/rmt/rtape1,/dev/rmt/utape1,/dev/xct0
/bin/dd if=CDEVICE1 of=CDEVICE2 bs=10240
Tape Drive 1
true
/usr/lib/tape/tapecntl -e /dev/rmt/c1b0t6l0n
BNCHMARKDLT1            5538
/dev/rmt/c1b0t6l0n
true
true
/usr/lib/tape/tapecntl -t /dev/rmt/c1b0t6l0n
/usr/lib/tape/tapecntl -w /dev/rmt/c1b0t6l0n
/usr/lib/tape/tapecntl -w /dev/rmt/c1b0t6l0n
true
qtape
cartridge
5.  Check "crontab -l" to determine when your backup is run and by
    what method.
Troubleshooting:
---------------
When I run a "tapecntl -r" command or "tape reset" to perform a test
tape reset, I get:

UX:tapecntl: ERROR: Device open failure. UX:tapecntl: ERROR: Please check tape or cables are installed properly. Operation may not be valid on this controller type.

- Before calling an hardware engineer to replace the drive:

1) Shut the server down and check the cables the boot the server. 2) Place a cleaning tape media in the drive (to clean the tape drive) 3) Place a new Tape media (not used one) and see if the night backup will work manually. 4) If not, then it's likely you have either a hardware issue with the tape itself or a cable issue or, less likely, with the controller the tape drive is attached to.

When adding a new tape drive:
----------------------------
1) OpenServer6 and UnixWare7 will automatically detect a tape drive
   upon a system reboot.  As long as the HBA controller the tape
   drive is connected to see's the tape drive at the boot stage then
   SCO unix should see it too.
If the devices are detected at boot time and 'sdiconfig -l' lists
the entry for a TAPE during the boot cycle, but, no tape is shown
after boot in 'sdiconfig -l', check that a flat file hasn't been
written to the /dev/rmt directory, which will prevent the new
tape device nodes from being created.  A typical reason for this
happening is a cpio or tar being written to /dev/rmt/ctape1 but
there is no tape drive connected so the backup is written to this
file on the root disk which may also endanger your root disk
space capacity too.

2) If not, then this is likely to be a driver or hardware issue.

3) For OpenServer6, once booted, it will not be necessary to run "mkdev tape" as required with OpenServer5.

# mkdev tape
Mass storage devices are configured automatically
when the system is booted with a new device present.
Current tape drive configuration:
Alias    - Address  - Inquiry String
--------   --------   --------------

See st01(7) for information about tape drive device nodes.

For both OpenServer6 and UnixWare7, the tape drive should be accessible as a device from /dev/rmt to be used with your backup commands, usually /dev/rmt/ctape1, eg. "cpio", "tar" or 3rd party tools such as BackupEdge, as examples.

See also

cpio(1)
tape(C)
tapecntl(C)
st01(HW)

TA116163, "How do I install UnixWare7 on a Compaq ML series server"

From the Xinuos technical article database, record 126646. Reproduced with permission. The original is at www.sco.com/ta/126646, which is reachable but blocked from search engines.

Next step

Need this fixed rather than explained?

Tell us the release, what the system runs and what it is doing. We will reply by email with what we would do next.

  • You deal with the people who do the work
  • No obligation, and no upgrade required before we will help
  • We tell you plainly if something is not worth doing

Send an enquiry

We reply by email. If a server is down, say so in the first line. You can also write to help@scoexpert.com.