Technical article 126835

The OS does not detect my hard drive or CD-ROM/DVD-ROM when I try to install the system.

OpenServer 6.0.0UnixWare 7.1.4

Written · Last revised

Problem

I am trying to install the operating system but my hard drive or ATAPI device is not detected. This happens with either an IDE hard drive or ATAPI device (e.g. DVD or CD-ROM drive) or a SATA device with the controller in a PATA (Parallel ATA or IDE) mode.

HARDWARE: An IDE hard drive or ATAPI device attached to a PATA (IDE) controller, or a SATA controller configured in a one of the PATA emulation modes, often called Legacy, Enhanced, or Compatible. In these SATA modes, the devices appear as PATA (IDE/ATAPI)) devices to the operating system.

Cause

The SCO IDE driver, named "ide", does not support what is called a "slave only" configuration. For PATA devices, this means that if there is only one device on either the Primary or Secondary IDE channel it must be configured as the master device. If there is only one device and it is configured as slave, the OS will not detect the drive.

In the case of Intel SATA chipsets with four ports, Ports 0 and 2 are mapped as Primary master and slave, respectively, and Ports 1 and 3 are mapped as Secondary master and slave. Therefore, if you want to configure a SATA device and it is the only device on the SATA bus, it must either be attached to Port 0 or Port 1. It must not be attached to either Port 2 or Port 3, as slave only configurations are not supported by the "ide" driver.

Also be wary of labelling, a SATA2 port may be the equivalent of Port 1 in the case above.

For example, during the installation of an Asus ts300 E7/PS4, the DVD/CD Rom was moved from SATA port 6 to SATA port 2 for the drive to be detected.

You may also encounter a SATA controller with only two
ports-- for example, the second SATA controller in an
Intel ICH9 chipset system.   In this case, if the
controller is in an IDE mode, Port 0 is master and Port
1 is slave, and a single device on Port 1 is not
supported.

Note that for SATA controllers, the above does not apply to a controller configured in AHCI mode. A controller in AHCI mode has no restrictions as to where devices are connected. Only a SATA controller configured in a a PATA mode (Legacy, Enhanced, or Compatible) is subject to the restrictions described above.

Solution

For IDE/ATAPI devices, reconfigure the device as master, rather than slave. A less common solution would be to connect another device as a master, such as another hard drive, CD-ROM drive, or a DVD-ROM drive.

For SATA devices, connect the device cable to either the Primary master or Secondary master connector on the motherboard.

A less common alternative solution would be to connect another device as IDE master or, for SATA, to the associated (Primary or Secondary) master connector.

NOTE:     If you see the following error:
/mnt/etc/conf/.new_unix doesnt exist
Installation aborted

Then this indicates the CD has been detected but there is a fault with the burnt image.

Flip to the console to see what HBA's have been detected and whether any CD read errors have been dectected with:

CTRL-ALT-ESC for UW7 (or CTRL-ALT-SYSRQ-H)

and to flip back to the installation you can use:

CTRL-ALT-F1 for UW7 (or CTRL-ALT-SYSRQ-F1)

From the Xinuos technical article database, record 126835. Reproduced with permission. The original is at www.sco.com/ta/126835, which is reachable but blocked from search engines.

Next step

Need this fixed rather than explained?

Tell us the release, what the system runs and what it is doing. We will reply by email with what we would do next.

  • You deal with the people who do the work
  • No obligation, and no upgrade required before we will help
  • We tell you plainly if something is not worth doing

Send an enquiry

We reply by email. If a server is down, say so in the first line. You can also write to help@scoexpert.com.