Technical article 126654

What is the Maintenance Pack 2 USB Supplement for OpenServer 6 and where can I download it?

OpenServer 6.0.0

Written · Last revised

Problem

What is the Maintenance Pack 2 USB Supplement for OpenServer 6 and where can I download it from?

Solution

The OpenServer 6.0.0 Maintenance Pack 2 USB Supplement provides support for USB Modem and USB Serial adapters.

This supplement is available to download from:

http://www.sco.com/support/update/download/release.php?rid=194

What follows are the release notes for this supplement.

                      OpenServer 6.0.0
                 Maintenance Pack 2 USB Supplement
                      Release Notes
**********************************************************
Dear SCO Customer,

OpenServer 6.0.0 Maintenance Pack 2 USB Supplement is an optional update for your OpenServer 6.0.0 Maintenance Pack 2 system.

Contents
========
  I)  Overview
 II)  Before Installing this Supplement
III)  Installing this Supplement
 IV)  Removing this Supplement
  V)  Supplement Notes and Limitations
----------------------------------------------------------------------------
I.  Overview
============
This OpenServer 6.0.0 supplement provides an enhanced USB driver that supports
both USB modems and serial adapters.  The device driver adds support for USB
modems that conform to the CDC/ACM specification.  Written to the Uniform
Driver Interface (UDI) specification, the new driver includes a number of
fixes that improve performance and device support.

Among the USB devices supported by this supplement are:

Zoom/Faxmodem 56K USB Modems (*) Allied Data Tornado SFM56.0-USB Modems All SeaLevel single and multiport devices Comtrol RocketPortII USB Serial Hubs MultiTech MultiModemUSB Modems CP-US-03 USB Serial Adapters VScom USB Serial Adapters BAFO Technologies BF-800 and BF-810 Single port adapters Serial Adapters that use the PL-2303 Chipset (**) Byterunner Technologies USB Communications Adapters. Serial Adapters that use the FT8U232AM Chipset (**) Modems supporting the "Abstract Control Model" Communications Subclass Interface type.

(*) Zoom has intermittent start-up failures due to firmware problems.

(**) If a vendor changed the product ID in PL-2303 and FT8U232 then the device may not work with this release.

If you have any questions concerning this supplement, please contact your SCO software supplier or your SCO Support Representative.

----------------------------------------------------------------------------
II.  Before Installing this Supplement
======================================

To install this supplement you must first:

1.  During your initial OpenServer 6.0.0 installation, install the

Universal Driver Interface (UDI) (ver 6.0.0Ni) Universal Serial Bus (USB) Support (ver 6.0.0Ni)

components.
NOTE:  Unless you deselected these components during ISL or you later
       removed them, they should be on your system.  If you need to
       reinstall these components, use your original OpenServer 6.0.0
       installation CD #1 or download the CD ISO image from:
	http://www.sco.com/support/update/download/release.php?rid=161
2.  Install OpenServer 6.0.0 Maintenance Pack 2 (MP2).
NOTE:  You can download MP2 from:
	http://www.sco.com/support/update/download/release.php?rid=133
3.  Install the OpenServer 6 Maintenance Pack 2 Supplement (OSS706, version B
    or later).
    NOTE:  To download the latest version of OSS706 version, click on the link
	   for oss706 in the "Patches" section of:
	http://www.sco.com/support/update/download/product.php?pfid=12&prid=20
----------------------------------------------------------------------------
III. Installing this Supplement
===============================

Follow these steps to install the OpenServer 6.0.0 Maintenance Pack 2 USB Supplement :

1)  Log in as root.
2)  Create an empty directory, such as /tmp/osr600usb, to which this
    supplement will be downloaded.
3)  Download the osr600usb.tar supplement from
http://www.sco.com/support/update/download/release.php?rid=194

to the directory created in step 2.

4)  Run:
	# cat osr600usb.tar | tar xvf -
5)  Run the Software Manager with the command:
	# scoadmin software

or double-click on the Software Manager icon in the desktop.

6)  Pull down the "Software" menu and select "Install New".
7)  When prompted for the host from which to install, choose the local
    machine and then "Continue".
8)  In the "Select Media" menu, pull down the "Media Device" menu.
    Select "Media Images", then choose "Continue".
9)  When prompted for the "Image Directory", enter "/tmp/osr600usb" (or the
    directory where you placed the VOL files in step 2) and choose "OK".
10)  When prompted to select software to install, make sure that the
     "OSS600USB - OpenServer 6 Maintenance Pack 2 USB" entry is highlighted.
     Choose "Install".
10)  Installation will take several minutes to complete.  When it does,
     to exit the Software Manager, select "Exit" from the "Host" menu.
11)  Once the installation has completed, you can remove or archive the
     downloaded patch, the media image files, and the containing directory
     created in step 2.
12)  Reboot your system:
	# init 6
----------------------------------------------------------------------------
IV. Removing this Supplement
============================
NOTE:  Patches must be rolled back in the reverse order in which they were
       installed on a per-component basis.
1)  Log in as root.
2)  Execute the command:
	# scoadmin software

or double-click on the Software Manager icon in the desktop.

3)  Highlight the "OpenServer 6 Maintenance Pack 2 USB Supplement" entry.
4)  Pull down the "Software" menu and select "Remove Software".
5)  Once the removal finishes, quit the Software Manager.
6)  Reboot your system:
	# init 6
----------------------------------------------------------------------------
V. Supplement Notes and Limitations
===================================

Once your system is rebooted any supported USB Serial and USB Modem devices connected to the system will be automatically recognized and device nodes for these devices will be created.

To list the serial ports of the USB devices that are recognized by your system run the the command:

	l /dev/usb_ser*
This will return output similar to:
crw-rw-rw-    1 root     root     295,108 Oct 24 10:05 /dev/usb_ser0A
crw-rw-rw-    1 root     root     295,107 Oct 24 10:05 /dev/usb_ser0a
crw-rw-rw-    1 root     root     295,106 Oct 24 10:05 /dev/usb_ser0h
crw-rw-rw-    1 root     root     295,105 Oct 24 10:05 /dev/usb_ser0s
/dev/usb_ser:
total 0
crw-rw-rw-    1 root     root     295,108 Oct 24 10:05 tty.03001-3.A
crw-rw-rw-    1 root     root     295,107 Oct 24 10:05 tty.03001-3.a
crw-rw-rw-    1 root     root     295,106 Oct 24 10:05 tty.03001-3.h
crw-rw-rw-    1 root     root     295,105 Oct 24 10:05 tty.03001-3.s
where

/dev/usb_ser0A is the modem control device /dev/usb_ser0a is the non modem control device /dev/usb_ser0h is the Hardware flow control device /dev/usr_ser0s is the Software flow control device

and
/dev/usb_ser/tty.03001.3.A
/dev/usb_ser/tty.03001.3.a
/dev/usb_ser/tty.03001.3.h
/dev/usb_ser/tty.03001.3.s

are USB Serial Device names for the serial ports where the first five digit number is the location of the host controller interface (HCI) to which the serial port/modem is connected. Its five digits represent the PCI bus number (two digits), the PCI device number (two digits), and the PCI function number (the final digit). For example:

/dev/usb_ser/tty.03001.3.A

The above device name indicates that the HCI is located at PCI bus number 03, PCI device 00, PCI function 1. Note that this number is completely determined by the hardware vendor's PCI configuration.

The remainder of the device name after the second period is a sequence of from one to six decimal numbers, each of which can be from one to three digits. The final number, which is required, indicates the port number on the device to which the serial port/modem is physically connected. Up to five hubs can be connected between the serial port/modem and the PC USB port, and the ports to which these devices are connected are indicated by the five optional three digit numbers in the device name, separated by periods.

In the example above, the serial port is connected to PC USB Port 3.

A device name like /dev/usb_ser/tty.00072.1.4.2 indicates the following device configuration:

PC USB Port 1 --- | Hub#1 Port 1
PC USB Port 2     | Hub#1 Port 2
                  | Hub#1 Port 3
                  | Hub#1 Port 4  --- | Hub#2 Port 1
                  ...                 | Hub#2 Port 2  --- USB Serial Port

You can use the Serial Manager to configure USB Serial Port devices. For details on configuring serial ports using the serial manager see:

http://osr600doc.xinuos.com/en/HW_io/config_trigger_level.html

You can use the Modem Manager to configure USB Modem devices. For more details on the modem manager see:

  http://osr600doc.xinuos.com/en/HW_modem/modem_manager.html
----------------------------------------------------------------------------

Document Issued: October 2006 Copyright (c) 2006 The SCO Group, Inc. All rights reserved.

From the Xinuos technical article database, record 126654. Reproduced with permission. The original is at www.sco.com/ta/126654, which is reachable but blocked from search engines.

Next step

Need this fixed rather than explained?

Tell us the release, what the system runs and what it is doing. We will reply by email with what we would do next.

  • You deal with the people who do the work
  • No obligation, and no upgrade required before we will help
  • We tell you plainly if something is not worth doing

Send an enquiry

We reply by email. If a server is down, say so in the first line. You can also write to help@scoexpert.com.