OpenServer 5.0.5 technical articles
888 articles from the Xinuos database that name OpenServer 5.0.5. Showing 651–700 of 888.
- How to set up user equivalence between two systems.
I want to set up user equivalence between two systems running SCO TCP/IP.…
- What are the recommended patches for retired operating systems?
I have a retired product and wish to check the essential patches required for this operating system.…
- Clients popping mail from the server are causing files to be left in /tmp on OSR5.
My clients are able to pop their mail successfully but some of them are causing files to be left in /tmp. The contents of the files are process ids.…
- STREAMS failure when using /etc/gated.conf "snmp yes" option.
Under certain conditions, there may be a STREAMS memory leak which may cause SCO OpenServer 5.0.0 (or later) systems to hang. On systems with Support Level Supplement (SLS) OSS449 (any versi…
- How do I force my 10/100MB autosensing Netelligent NIC to run at a specific speed?
I want to lock my ethernet speed on my autosensing 10/100MB Netelligent NIC.…
- Can I run the IRD protocol with RIP or OSPF, that is, with routed or gated?
A section in the /etc/tcp file says to start irdd (IRD) completely commented out, stating that you must NOT run irdd with gated or routed:…
- Configuring primary nameserver for multiple domains using the same network address for each domain.
Separate domains would usually get their own configuration files, so the domain "xyz.com" would have its A records in a file named something like "xyz.hosts", and its PTR records would typic…
- Basic troubleshooting for sendmail.
There are several reasons why sendmail may not work. Follow the steps below to narrow down the problem, and collect information needed to solve the issue.…
- How can I determine which NIC is net0 or net1?
After installing more than one network card, how can I determine which NIC is net0, net1, net2, and so on?…
- How to set up a basic sendmail configuration.
If you are converting from MMDF to sendmail, see TA107593, "How do I change from MMDF to sendmail in SCO OpenServer Release 5?" for instructions on removing MMDF from your system and install…
- OpenServer 5, How do I automate netconfig(ADM) to add an ethernet card on a TCP chain?
How do I automate netconfig(ADM) to add an ethernet card on a tcp chain?…
- Configure telnetd to close connection when client connection no longer exists.
Commands such as who(C), finger(C), and ps(C) may show established telnet sessions when the client end of the TCP connection no longer exists, for example, when the client computer crashes, …
- Routes are mysteriously showing up in my routing tables.
My system is not running routed, gated, or ird'd, yet my netstat -rn shows new routes. How are they getting there? The netstat -rn output also shows a "D" in the flags section for these rout…
- Installing a network card fails with message "/usr/lib/netconfig/init/net1 net1--sco_tcp lli Y does not exist".
I am attempting to install a network card and it is failing with the following message:…
- I installed a network interface card (NIC); now I'm having networking problems.
(1) The NIC is configured successfully but doesn't respond or gives errors during reboot;…
- How can I configure sendmail to deliver mail through UUCP exclusively and not use SMTP at all?
I want to configure sendmail to deliver mail exclusively through UUCP and not use SMTP.…
- How can I get sendmail to recognize a new hostname?
After changing hostname with uname -S, the old server name still shows up in the "From:" field of outgoing email. How can I get Sendmail to recognize a new hostname?…
- How can I bypass the filter on a non-SCO lpd server using lp(C)?
I want to print a file from an SCO system to a non-SCO lpd server and I want to flag to the lpd server not to filter the file before printing it. BSD versions of lpr provide a -l (literal) o…
- How do I configure sendmail for an intranet environment without DNS?
1. Rename /etc/resolv.conf to /etc/resolv.conf.bak, if it exists.…
- How do I configure sendmail to ignore case-sensitivity when looking up local usernames in mail addresses?
How do I configure SendMail to ignore case-sensitivity when looking up local usernames in mail addresses?…
- What IP addresses can I use for an internal (private) network?
I am building an internal, or private, network and would like to use addresses that are not currently used on the Internet.…
- How to turn on ftp logging.
In the file /etc/ftpaccess, uncomment the following line:…
- I get "ftpd[xxxx]: #2 open of pid file failed: No such file or directory".
ftpd[xxxx]: #2 open of pid file failed: No such file or directory…
- I get a "/etc/slink: Function "boot_net0" redefined" error during kernel relink.
While relinking the kernel after removing or reconfiguring my network card, I see this slink error:…
- rcp(TC) and rcmd(TC) fail with stty related error messages when using the csh.
When I use the rcp(TC) or rcmd(TC) commands to interface with a remote machine, and the remote login is running a csh, the command fails and the following message is displayed:…
- How can I set ipforwarding and ipsendredirects from the command line?
To set your system up as a gateway, take your system into System Maintenance mode and issue the commands:…
- Is it possible to configure multiple default routes in OpenServer 5?
To provide increased resilience to failure, a site has been configured with multiple connections via routers to an external network.…
- How do I change from MMDF to sendmail in SCO OpenServer Release 5?
In order to switch mail packages, you must first remove the mail package that is currently installed on your system and install the new mail package from your installation media. This can be…
- How do I add a default route statement so it's included at boot-up in OpenServer 5.0.X?
The 'route add default' statement should be added in the /etc/rc2.d directory. In SCO Open Server 3.0, the route add statement was included in /etc/tcp or /etc/rc.d/8/userdef. However, in SC…
- Need utility that displays ip number and port of remote host.
I need a utility that will display the ip number and port of the remote host I logged in from.…
- Get "copy file too large" error when initiating remote print job.
I received the error message "copy file too large" when I initiated a remote print job from the client.…
- How do I set up a primary nameserver and nameserver clients?
What files need to be configured to set up a Nameserver?…
- OSR5:Remote backups over an SCO TCP/IP network using cpio and rcmd.
(A) Backing up remote system to a tape drive on the local system.…
- What are the recommended patches for retired operating systems?
I have a retired product and wish to check the essential patches required for this operating system.…
- Slow parallel printing
I have a very slow parallel printer. Is this normal for SCO XENIX, or is there something I can do about it?…
- Df(C) and mount(ADM) report erroneous information.
To recreate the mount table from scratch, issue the following command:…
- Why did my UNIX kernel "panic"?
System panics can be caused by hardware or software problems. The following procedure can be used to diagnose the cause of some system panics.…
- Configuring MMDF in a UUCP environment under SCO UNIX operating systems.
How to configure the MMDF mail system in a UUCP environment under SCO UNIX System V/386 Release 3.2, SCO Open Desktop, and SCO OpenServer 5.…
- How do I bring focus to X Windows with my mouse pointer?
I want my X Windows to come to the foreground when I move my mouse pointer on them _without_ having to click my mouse buttons. How do I do this?…
- Unable to set IPX source routing with token ring on SCO OpenServer Release 5.
Running netconfig to add a token ring NIC, then configuring IPX/SPX protocol and choosing Advanced Options to select "yes" for source routing with IPX/SPX and "save", results in this error:…
- My X-application compiled with 5.0.4 libXm.a library scrolls in a jerky manner.
An X-application that was compiled with SCO OpenServer 5.0.0 and 5.0.2 libraries allowed smooth scrolling and generally worked fine. However, the same X-application compiled with SCO OpenSer…
- The pages print filter does not work as documented under SCO OpenServer 5.
I am trying to use the filter command to print a specific page or group of pages from a text file. I have followed the example in the System Administration Guide Chapter 4, but when I use th…
- SCO OpenServer installation bootstring options.
SCO OpenServer 5.0.4, 5.0.5 or 5.0.6, 5.0.7 is not installing properly.…
- How do I create customized system dump images on demand?
a) Create a system dump image on the running system, without disrupting the normal operation of the system, and save this image to a file, automatically incorporating within the file the ker…
- In OpenServer 5.0.x, I don't have enough swap space to complete a panic dump.
Moving the dump device to a different drive or partition requires two steps:…
- Non-root users can't use "-o nobanner" when printing to HP JetDirect printers.
When a non-root user specifies a print request with no banner, for example, "lp -o nobanner my_printer" to an HP JetDirect printer, the following error message is displayed:…
- How do I configure my 5.0.x server as a gateway?
Before following the steps for configuring the server as a gateway, draw a picture of your network like the one above, filling in the appropriate IP addresses for your setup. With or without…
- SCO OpenServer IFS 5.0.4 system doesn't see any additional CPUs even though SMP is licensed properly.
I have installed and licensed SCO OpenServer Internet FastStart Release 5.0.4 onto my multiprocessing system. I have also installed and properly licensed SCO SMP (Symmetrical Multiprocessing…
- OpenServer 5 network-capable boot diskette fails with error "slink: can't open '/etc/strcf'."
I have followed the procedure in the SCO OpenServer 5.0.4 Handbook, Chapter 5, entitled "Creating an emergency boot floppy disk set" and added the listed files to make a network-capable boot…
- I get the message "prc_sync: script (P86sendmail) failed to complete 120 seconds."
I am getting the following message when trying to boot to multiuser mode:…
Other releases: OpenServer 5.0.7 · OpenServer 5.0.6 · OpenServer 6.0.0 · OpenServer Definitive 2018 · OpenServer 5 · OpenServer 6
Running OpenServer 5.0.5?
These articles are the vendor's own. If you would rather have the work done, or something is broken right now, tell us what the system is doing.
- You deal with the people who do the work
- No obligation, and no upgrade required before we will help
- We tell you plainly if something is not worth doing